The Complete Beginner’s Guide to Ball Valve Maintenance

 

Are all the ball valves on your boat easy to turn? Do you know where they all are? Do they seal completely? Have you ever done any maintenance to them? They’re not maintenance-free. In this post, I will dispel any mystery about how ball valves work and walk you step-by-step through how to take one apart, inspect it, and lubricate it.

Ball valves are the type most often found on boats compared to other types such as gate valves and butterfly valves. They are also known as seacocks when they are mounted near a hull opening to either admit water from or expel water to outside the hull. They’re called ball valves because they use a solid ball with a hole through its middle to control the flow. The ball rotates with the handle to align the hole with the inlet and outlet to allow flow. Turned 90 degrees, the inlet and outlet are blocked and prevent flow. They are best used as shutoff valves because they only need a quarter turn to operate and because the position of the handle conveniently indicates the state of the valve, either open or closed.

Ball valves are not very high maintenance parts. Other than worn O rings that seal the ball inside the valve body, keeping the valve clean and free-turning with a little lubrication is all they need. It’s when a valve looses its lubrication and debris or corrosion builds up that it can become hard to turn. If you apply too much force to a plastic valve, the handle can break off leaving the valve inoperable and you must repair or replace it.

Keep the ball rolling

Follow these steps to maintain a ball valve:

1. If practical, remove the valve from the boat so you can inspect it and work on it more easily.

2. Clamp one end of the valve firmly in a vise but not so tightly that you deform or crack the valve.

3. With the large wrench, unscrew the other end.

DSCN2432
Years of corrosion can make valves difficult to disassemble. A vise helps to hold the valve stationary for more leverage.

4. Use water to flush out any sand and dirt from both parts.

The particular valve shown in this post was on the galley drain hose that connects to the cockpit scupper drains above the through-hull fitting on Summer Dance. The valve angles downward slightly away from its outlet and so acts like a sediment trap for the cockpit drains. Normally, valves like this should at least be angled toward the through-hull so that they don’t trap debris. Unfortunately, the drain funnel that feeds into this valve is too low for that. In situations like this, clean the valve more often than normal to minimize the scoring shown below.

DSCN2433
Dirt and debris can catch in a valve that isn’t angled toward its outlet

5. Turn the valve handle to the open position, remove the screw that attaches the handle to the valve, and pull the handle straight off.

6. Reach inside the valve body with one finger, stick it in the ball hole to grip the ball, and rotate the ball back and forth until you can pull it out. It should be tight but come out with enough persuasion. The hardest part is getting the handle stem out of its hole.

DSCN2438
Disassembled ball valve. There are typically three O rings that seal it watertight.

7. Clean all the parts thoroughly with soap and water. Inspect the O rings for wear and replace as necessary. If the ball and valve body are excessively scored or worn to the point that the valve leaks too much when closed, replace the entire valve.

DSCN2439
Valve ball scored by sand and grit

8. Apply a good quality silicone or Teflon marine lubricant to the O rings and wear surfaces.

DSCN2444
Lubricate the valve for easier operation and longer life

9. Reassemble the valve in the reverse order. Reinstall the small O ring between the ball and handle after you reinstall the ball or it could get pinched in the valve body and prevent proper fit of the other parts. Be sure it seats fully before you reinstall the handle.

10. Reinstall the valve in the boat. Apply Teflon tape to any threads and check for leaks and proper operation.

Repeat this job every couple of years depending on how often you sail and how often you use the valve. At a minimum, work all valves annually to prevent them from sticking.

Advertisements

2 Comments Add yours

  1. James McPherson says:

    My ’72 model has a metal seacock that is stuck open. I guess it is brass? I would like to keep it but need to clean it up. So far I have just shot liquid wrench in it in place from one scupper hose inlet and outside around the handle rotating part. Any suggestions? thanks James

    1. Hey, James

      If it has the lever on the side, it’s probably built the same as a plastic seacock but with a brass body and you can take it apart the same way. The ball is probably frozen inside from corrosion. I’ve yet to find anything that effectively dissolves it, even mild acids. I think you’re going to have to overhaul it.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s