Quick and Simple DIY Turnbuckle Boots

This week’s project is one of the easiest you’ll ever do to your sailboat. There’s no epoxy, painting, drilling, wiring, or splicing involved. If you can saw through a piece of PVC pipe, you can do this job. Heck, this might be a good project for a junior crew member to work on their stingy sailor skills!

Before I continue, a bit of legal housekeeping. This post contains affiliate links. That means I receive a small commission if you make a purchase using those links. Those commissions help to pay the costs associated with running this site so that it stays free for everyone to enjoy. For a complete explanation of why I’m telling you this and how you can support this blog without paying more, please read my full disclosure.

Give Chafing the Boot!

Turnbuckle boots protect your expensive running rigging and sails from chafing on your turnbuckles and snagging on cotter pins. If you’ve been eyeing a set of Davis Instruments Turnbuckle Boots for your sailboat at about $6 a piece, you’ll be glad to know that you can make your own turnbuckle boots for under $1 a piece.

All you need is one 10′ piece of white 1″ diameter schedule 40 PVC pipe from your favorite home center. Don’t buy schedule 80 pipe. It has a thicker wall and smaller inner diameter and it costs more, none of which make it any better for this project.

One inch diameter pipe is large enough to fit over most turnbuckles on small sailboats but not so big that it slips over the T bolt toggles and off the ends of the shrouds. The diameter is important because you want to slide them up off the turnbuckles so that you can adjust them when you need to, but you don’t want them to slip off the turnbuckles every time you disconnect a shroud from its chain plate.

Cut all the lengths that you need from that one 10′ piece. You can cut the PVC pipe with just about any saw that will cut wood. A miter saw works well but a hand saw will work if that’s all you have. Cut the boots for the upper shrouds and aft lower shrouds at least long enough to cover your turnbuckles. I cut mine 12″ each. For the forward lower shrouds, you have two choices.

Tack ‘n Roll

If you keep your sailboat in a slip most of the time, you can cut the forward lower shroud boots long enough to work as shroud rollers (also called rigging rollers). Shroud rollers reduce the chafing caused by your foresail rubbing across the shrouds when tacking. Instead of the sail dragging across the rigging, the sail rolls across on the shroud rollers. The rollers can also prevent the jib sheet clew knot from hanging up on the rigging. If you heave to often, especially in moderate to heavy winds, your headsail can take a beating. Shroud rollers eliminate that chafing too.

If you want to cut the forward lower shroud boots long enough for shroud rollers, you’ll need to buy two 10′ long pieces of PVC. Cut one pipe in the middle for the two forward lower shrouds and cut the rest of the boots from the other piece.

If you trailer sail, I recommend that you cut the forward lower shroud boots the same length as the others. That makes them easy to secure for transport. If you make them 5′ long for shroud rollers, they’ll be a hassle to handle when stepping and unstepping the mast and when storing for transport.

If you trailer sail and want the protection of shroud rollers without the hassle, consider using snap-on cable covers one size too big for your rigging. Instead of a tight fit, they’ll roll like rollers but bend easily for convenient handling.

After you have your turnbuckle boots cut to length, round over the sharp edges on each end with sandpaper. To remove the ink printing on the pipe so your boat doesn’t look ghetto, wipe it off with acetone. Follow up with a coat of Armor All and they’ll look great!

Remove each turnbuckle from its shroud to slide a boot onto the shroud, then replace the turnbuckle. If you have quick release levers below your forward lower shroud turnbuckles like I do, the levers should hold the boots over the turnbuckles and out of your way when working the lever. While you’re at it, this is a good time to make sure your chain plates tabs are all pointing toward the mast.

Forestay Quick Release

Don’t worry about not having caps on top like the Davis boots, they don’t do much and you won’t miss them (or lose them!).

The Bottom Line

Suggested price: $43.51

$tingy Sailor cost: $3.93

Savings $39.58


Would you like to know when I publish more posts like this? Enter your email address below to subscribe to this blog and receive notifications of new posts by email. You will also receive occasional newsletters with exclusive info and deals only for subscribers and the password to the Downloads page. It’s free and you can unsubscribe at any time but almost nobody does!

Enter your email address to follow this blog and receive notifications of new posts by email.

 

Advertisements

One Comment Add yours

  1. Jacktar says:

    I made a similar gizmo of PVC and a plug to put the hanks above the turnbuckle on my Cat 22

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s