Turn a Locker Lid into a Cockpit Table

At the risk of overstating the obvious, trailerable sailboats are cramped. Some are more cramped than others. Cramped inside and cramped outside. But we tolerate the cramped conditions because they’re so much fun to sail and to camp aboard. That doesn’t mean that they can’t be made more comfortable.

Before I continue, a bit of legal housekeeping. This post contains affiliate links. That means I receive a small commission if you make a purchase using those links. Those commissions help to pay the costs associated with running this site so that it stays free for everyone to enjoy. For a complete explanation of why I’m telling you this and how you can support this blog without paying more, please read my full disclosure.

When the weather is great and you’re anchored in a secluded cove at dinner time and there’s an amazing sunset happening, do you regret having to go down into the cabin to eat at a cramped dinette? I sure do. I’d much rather eat topside and soak in the natural surroundings and not miss a minute of the night’s light show.

You don’t have to envy those big motor yachts and pontoon boats with their spacious cockpit dining tables. And you don’t have to spend hundreds on a complicated upgrade that will put holes in your boat the size of the void left in your wallet from their cost.

For a few dollars and a couple of hours of your time, you can have a simple, sturdy, and space-efficient cockpit table by re-purposing a part of your sailboat that you already have.

Put a lid on it!

Most sailboats have storage lockers of some kind in the cabin space. While you’re serving dinner, don’t you normally get food, dinnerware, and other supplies out of at least one of those lockers? We do aboard Summer Dance.

Rather than removing and replacing the lid over and over or leaving it off where it just gets in the way, you can modify it to work temporarily as a cockpit table. After dinner, when the cleanup is all done, you can switch it back from cockpit table to locker lid.

This project has only a few parts:

  • One locker lid. Choose a lid that is handy to take off at dinnertime and is the best size for your cockpit; big enough to be useful but still leaves room around it for seating.
  • Two rubber pole clips (Sea Dog Line Pole Storage Clip White 5/8″ or similar) to fit the main sheet traveler bar, pushpit rail, or transom edge. Attach them to the lid 1″-2″ inward from the edge so that they clear the locker opening when the lid is being used as a lid instead of as a table. Depending on the configuration of your cockpit, you might have to get creative here with a different attachment method to support the aft edge of the locker lid than I show here.
DSCN4550 (Custom)
Lid secured to the main sheet traveler bar by rubber pole clips

With the aft edge of the locker lid supported, you want to support the front of the lid at one point with the tiller handle. The three points together make a stable base for the lid.

On my Catalina 22, the height of the autopilot bracket on the tiller and the height of the traveler bar are nearly identical and hold the lid fairly level. I drilled a shallow hole in the bottom of the lid for the autopilot pin to sit in. The goal here is just to prevent the tiller from accidentally getting bumped out from under the locker lid and spilling your dinner down the cockpit scuppers.

DSCN4529 (Custom)
Autopilot pin engaged in the middle hole. Note a secondary hole on the far edge of the table/lid

For more information about autopilots and to see how the autopilot bracket attaches to the tiller, go to How to Install a Tiller Autopilot.

For more leg room under the table, drill extra holes near each edge so that the tiller can be swung to either side of the table and locked in place there. The table will almost seem to float in space yet it should be strong enough to hold dinner for at least two stingy sailors.

DSCN4548 (Custom)
Tiller swung to starboard and locked in one of the secondary holes

If you don’t have a suitable autopilot bracket but your tiller sits high enough, consider attaching a third, larger pole clip to the bottom of the locker lid to grip the tiller.

Give it a leg to stand on

Another option is to build or buy a short folding table leg (AP Products 013-071 Folding Table Leg or similar) that you can attach to the bottom of the lid but fold up and secure so that it’s out of the way when the lid is back on the locker. Again, make the leg short enough and attach it 1″-2″ inward from the edge so that it clears the locker opening when the lid is being used as a lid instead of as a table. As a last resort, I’ve also seen tables suspended from the boom by a short accessory cord. Choose the option that works best for you.

You can further customize your locker lid/cockpit table with drink holders, non-skid surface, fiddle edges, and so on. The cockpit flood light attached to the pushpit rail in the first picture was featured in Add a Solar-Powered Flood Light in Your Cockpit. It works great for illuminating the table if it’s extra dark. If you want to get even fancier, make a replacement lid out of varnished teak plywood or other material of your choice. Guests to your sailboat will marvel at your ingenuity!

Would you like to be notified when I publish more posts like this? Enter your email address below to subscribe to this blog and receive notifications of new posts by email. You will also receive occasional newsletters with exclusive info and deals only for subscribers and the password to the Downloads page. It’s free and you can unsubscribe at any time but almost nobody does!

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

2 Comments Add yours

  1. Rebekah Simmers says:

    I haven’t been able to locate any teak veneer, or board, other than scavenged off of other boats. Do you have any suggestions??
    I really like the idea of that table but am missing the locked lid.
    Thanks !!

    1. Hi, Rebekah

      There are teak suppliers online but a piece of veneer plywood is going to be expensive to ship and you won’t get to pick it out. You could also make it out of medium density fiberboard (MDF) and paint it with a marine enamel like mine. Low cost and easily replaceable.

      Hope that helps,

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.