Whether or not you’ve replaced your standing rigging, you may be wondering how to adjust it. How tight should the rig be? How can you measure it? After all, what good is great rigging if it isn’t tensioned properly to perform its best?
Before I continue, a bit of legal housekeeping. This post contains affiliate links. That means I receive a small commission if you make a purchase using those links. Those commissions help to pay the costs associated with running this site so that it stays free for everyone to enjoy. For a complete explanation of why I’m telling you this and how you can support this blog without paying more, please read my full disclosure.
A properly tuned rig isn’t only important for racing, it’s also a good idea for cruisers. It minimizes uneven stress and wear on hardware, it’s safer, and it protects the shape of your sails.
Close only counts in horseshoes and hand grenades
Unfortunately, without a tension gauge, tuning your rig is mostly subjective guesswork.
The 1987 (last) edition of the Catalina 22 Owner’s Manual and General Handbook puts it this way:
Adjust forestay and backstay so that the mast is straight up and down.
The upper shrouds should be firm but not far apart. A 50 pound push should deflect the upper shroud about 1″ at shoulder height.
The lower shrouds (4 of them) should be adjusted so that they are looser than the upper shrouds. While at dock, they should have no slack, but no tension either. No lower shrouds, when pushed, should deflect the mast more than any other shroud when pushed equally hard. If this can’t be achieved, the upper shrouds are too tight. Back off one-half turn at a time on the upper shroud turnbuckles until the tension of the lower shrouds is brought into balance. [Emphasis added]
Not very precise, huh? It doesn’t take very much tension at all on the forestay and backstay just to make the mast plumb and that’s too loose for anything but light air sailing. How much is “far apart?” How exactly do you measure a 50 pound push horizontally against a wire at shoulder height? Standing where, on the cabin or on the deck? How much is “looser” but “without tension?” How do you measure balance between four shrouds without a tool?
That’s like your mechanic telling you that the best way to tune your car’s engine is by ear alone so that it idles well but not too fast and not too slow. It should accelerate smoothly with good power but no cylinder should exceed 10% less compression than any other.
You can’t lose with a Loos
You can skip all the guesswork with a tension gauge. Loos & Co. has manufactured cable in the US for over 50 years. They make the most popular and economical tension gauge for sailors. It’s available in several models depending on the range of cable sizes that you want to measure.
The current model numbers are:
- PT-1 (3/32″ to 5/32″)
- PT-2 (3/16″ to 1/4″)
- PT-3 (1/4″ to 3/8″)
Older models of the gauge can still be found for sale new and used:
- Model A (3/32″ to 5/32″)
- Model B (3/16″ to 9/32″)
The major differences between the newer models and the older models are:
- The older models use a flat spring built into the gauge to measure the tension. The newer models use a coil spring.
- The older models have a slot for the cable. Measuring very tight cables can produce a very slight kink in the cable. The newer models have two round, plastic guides that don’t harm the cable.
- You read the tension on the bottom of the older models. This means you either have to stoop down to read the gauge or use the gauge over your head. You can read the tension on the front of the newer models from a more natural stance.
- The older models have fewer parts and are all metal construction except for the lanyard. The newer models have more parts, some of which are plastic.
- Unlike the older models, the newer models can be hooked onto the cable while you are measuring it so that you can read the tension and your hands are free to adjust the turnbuckle. This is a nice feature that reduces trial and error.
Each gauge has handy notches in the side for measuring cable diameter.
The gauges work on the principle that if you bend a cable by applying a specific amount force, it will bend more or less depending on the size of the cable and how much tension is on the cable. The larger or the more tension on the cable, the less bend. The smaller or the less tension on the cable, the more bend. The gauges use a spring (flat or coil) to measure the amount of bend that results when you bend a cable slightly and they convert that amount into a tension number.
Dialing it in
I use my gauge whenever I modify my standing rigging in any way and periodically to recheck it, especially because I step the mast for every launch.
To measure tension with an older model Loos gauge (the process is slightly different for the newer models):
1. Hook the gauge on the cable. If you have cable covers on the cable, the gauge won’t fit over them, hook the gauge on a bare part of the cable. You read the gauge from the bottom so hook it over your head.
2. Pull the lanyard until the indicator aligns with the mark on the gauge.
3. Read the (bend) number from the scale.
4. Measure the cable size and look up the tension in pounds that corresponds to the cable size in the chart on the gauge. This step is optional unless you’re trying to set the tension to match a recommendation stated in pounds of tension (300, for example). Some recommendations are stated as the equivalent and easier to remember scale number (24, for example). In that case, you don’t need to look up the tension in pounds.
When you know the cable’s tension, you can adjust its turnbuckle to either increase or decrease the tension by measurable amounts. With a little trial and error, you can “dial in” a very accurate amount of tension. Dial in all of your stays and shrouds, and you will have a well-tuned rig. For instructions on using the new model gauges and a video, go to How to use PT Series Tension Gauges.
Once you get your basic rig tension set, you only need to remember the scale numbers and you can confidently adjust it to best suit your style of sailing or changing conditions. There are good guides available online that recommend settings for different conditions. One of the better ones for the Catalina 22 is the Catalina 22 Tuning Guide from North Sails. They have guides for other sailboats as well.
If you don’t know anybody that you can borrow a gauge from, consider getting one of your own from Amazon. Then you’ll have one to loan to others in need.
Stop hoping that your rig tension is close enough. Tool up and dial it in!
Would you like to be notified when I publish more posts like this? Enter your email address below to follow this blog and receive notifications of new posts by email. You will also receive occasional newsletters with exclusive info and deals only for followers and the password to the Downloads page. It’s free and you can unsubscribe at any time but almost nobody does!