It seems that every C-22 owner upgrades their cabin lighting at some point. The original dome lights are not very bright or sturdy and their incandescent bulbs use a lot of battery power. In Summer Dance, the previous owner had replaced the two salon dome lights with the combination white/red LED lights from a certain Catalina parts dealership. They don’t use much power but they also don’t put out much light either.
600 LEDs to the rescue
I happened across a thread on a SailboatOwners.com forum that was started by an owner who had installed waterproof LED strip lights in his C-22. He had installed one self-adhesive light strip on each side of the boat. There is a narrow channel in the underside of the deck where it meets the hull that is just the right size for mounting the strips so that they are mostly hidden. I liked the idea, low power consumption and widely distributed indirect light. The strips are dirt cheap on eBay so I thought I’d give them a try. But I wanted to take the idea a step further and create two lighting zones by installing two strips (one on each side) in the V berth and another two strips (one on each side) in the salon in a way that they could be independently switched.
Each 8mm wide x 5 meter long strip has 300 tiny tightly spaced 12V LEDs. The LEDs are surface-mounted on a flexible conductor strip encased in silicone and has peel-and-stick adhesive on the back. You can cut the strip at 3 LED intervals to any length you need. The strips are available with standard 3528 or 5050 type LEDs and either warm white or cool white color temperatures. The 3528 LEDs require less power and are less bright than the 5050 LEDs. I chose the 3528 type for lower power consumption, 4.8 watts per meter. That amounts to about as much current per side of the boat as one of the original incandescent dome lights. They still put out plenty of light for the inside of a sailboat. If you decide to try this project, get the warm white color. It’s the most natural color temperature. The cool white color is harsh.
In planning the installation, I got stuck on deciding how to switch the lights on and off. I couldn’t find a surface mounted switch that was both easy to use and unobtrusive. I didn’t want to mount switch boxes or bulky teak switch plates on the bulkheads. The solution needed to be more elegant than that. Then while shopping for the right seller to buy the strips from, I found the answer, a two-channel wireless remote dimmer. No switches to mount and the lights could be controlled from anywhere on the boat. I could connect each zone to a separate channel of the dimmer and control them both with one remote. Here’s a link to an eBay listing for the dimmer.
Along with the light strips and dimmer, I also ordered some solderless connectors to connect each pair of strips in series to separate channels of the controller. The connectors help to make the connections between strips. At first, I wired the two salon strips in parallel to the controller but that didn’t work. I wound up wiring them in series by running wires from one side of the cabin to the other under the V berth.
I removed the teak molding at the deck/hull joint to make it easier to mount the light strips. They are flexible enough to bend around the curve of the hull. Be sure to clean the mounting surfaces thoroughly with alcohol or a similar solvent to improve adhesion. Although the lights held in place for a couple of weeks after mounting them this way, they eventually wouldn’t stick in the deck channel. The strips have excellent 3M adhesive, but the rough surface in the fiberglass deck channel doesn’t provide enough contact area, at least on Summer Dance. I later reinstalled them with one of my favorite products, 3M Scotch-Mount Super Automotive Attachment Tape, and they’re holding well now.
I connected 16 AWG positive and negative primary wires to the pre-wired leads with crimp-on heat shrink butt connectors and ran the wires to the dimmer receiver, which I mounted under the aft settee seat. I ran the V berth zone wiring on the starboard side, down through a 1/2″ hole that I drilled in the hull liner at the aft bulkhead, and then under the liner to the dimmer receiver. I also ran the salon zone wiring under the liner to the dimmer receiver. I connected power to the dimmer receiver from the nearby breaker panel and negative buss. The dimmer doesn’t work with shared negative wires. Each strip needs a dedicated negative conductor to the dimmer receiver. And when wiring the strips in series, observe the polarity or else one strip won’t work.
After struggling with the sparse, poorly translated instructions to pair the remote control to the receiver, I turned on the strips with one touch of the remote control and viola! The whole cabin filled with bright, warm light. (By the way, all the cabin photos in this post were shot at night without flash and only the LEDs for lighting.) Each zone can be dimmed independently until it is completely off. Both strips can be dimmed together with the soft-touch dial on the remote control. You can only see the LEDs while laying down. When we only need a little task lighting in the salon, we can turn on the LED dome lights.
After the cabin was finished, I had about 8′ of LEDs left over so I installed one 2′ strip on the underside of the drain channel behind each lazarette lid. They are controlled by a switch in the accessory panel that I installed near the companionway.
They’re really convenient for using the lazarettes or just to illuminate those storage areas from inside the cabin.
The Bottom Line
Suggested price: n/a
$tingy Sailor cost: $54.49
How have you improved the lighting in your cabin?